This is a general checklist for anyone evaluating a humate product before it is considered for pond use. Our sodium humate TDS does not list aquaculture use, and this page does not recommend any product, including ours, for ponds.
Humates are made from natural raw materials such as leonardite and lignite, and products sold under the same name can differ in solubility, insoluble residue, alkalinity, sodium content and impurities. A pond is a largely closed system: whatever is added stays in the water and the sediment, and fish, invertebrates and plankton are exposed to it directly. The checks below help a buyer compare products on the same terms and decide whether a product should be considered at all.
Why humate products need checking
Grades made for industrial binders, drilling fluids or soil application are specified for those uses. Their TDS lists the properties that matter there, such as humic acid content, moisture and solubility, and may say nothing about properties that matter in water, such as impurities. Composition also depends on the raw material and the process, so one supplier’s figures cannot be assumed for another’s product.
1. Solubility and insoluble matter
- Ask for the water solubility figure on the TDS and how it was measured (sample-to-water ratio, temperature, filtration).
- Ask for the insoluble matter figure. Insoluble residue does not disappear in a pond; it settles and becomes part of the sediment.
- Dissolve a sample in the actual pond water, not distilled or tap water. In hard water, calcium and magnesium ions can cause dissolved humate to flocculate, so a product that dissolves fully in soft water may leave sediment in pond water.
2. pH and sodium content
Soluble humates are alkaline salts. Our sodium humate TDS, for example, lists a pH of 9–10. Ask for the pH and the dilution at which it was measured, because figures measured at different dilutions cannot be compared. Adding an alkaline product raises water pH, especially where alkalinity is low.
A sodium humate also adds sodium to the water. Ask for the sodium content, or at least confirm which salt (sodium or potassium) the product is, and consider it alongside the water’s existing sodium and salinity.
3. Heavy metals
Because humates come from natural deposits, their content of heavy metals depends on the raw material. Ask your supplier for a heavy-metal test report covering at least lead (Pb), cadmium (Cd), arsenic (As), mercury (Hg) and chromium (Cr), and compare the results with the limits that apply in your country.
- Check that the report names the laboratory, the test method and the batch it refers to.
- Check the date. A report on an old batch says little about the batch you will receive.
- An independent third-party laboratory report carries more weight than a figure typed into a sales document.
Humic substances carry carboxyl and phenolic groups that can bind metal cations; the chemistry is explained in Humic Acid in Soil Remediation. That binding is one reason to know what metals the product itself contains.
4. Dry or as-is basis, and test methods
Humic acid content can be reported on a dry basis or on an as-is basis (including moisture). A dry-basis figure is always higher than the as-is figure for the same material, so check which basis each supplier uses and check the moisture content.
Different analytical methods for humic and fulvic acids also give different numbers for the same sample. Ask which method was used and compare products only when the method and basis are the same. A higher number from a different method is not evidence of a better product.
5. Documents to ask for
- Technical data sheet (TDS). Typical properties and the uses the product is specified for. Check whether pond or aquaculture use is listed. If it is not, the product is not specified for it.
- Safety data sheet (SDS). Hazard classification, handling, storage and disposal. Our sodium humate SDS lists it as not classified, and its ecological section states that no aquatic toxicity data are available. An SDS classification is not an aquatic safety assessment: it does not tell you how a product affects fish, invertebrates or plankton in a pond.
- Certificate of analysis (COA). Measured values for the specific batch, compared with the TDS.
- Third-party test report. Independent results, for example for heavy metals.
6. Local regulations
Many countries regulate which chemicals may be added to aquaculture ponds and what may be discharged from them. Check with the competent authority before buying, and keep the documents above on file.
7. Start with a small pond trial
If a product passes these checks and its use is permitted, test it first in a small pond with an untreated control pond, ideally with an aquaculture specialist. Record dissolved oxygen, pH, alkalinity, ammonia and nitrite before and after, and look at water colour and the condition of the stock. Pond water quality principles, including how pH, alkalinity and light interact, are covered in standard texts such as Boyd and Tucker (1998).
Risks and limits
Dissolved humic substances are not inert in water. Steinberg et al. (2006) reported in their review that dissolved humic substances taken up by aquatic organisms can act as a mild chemical stressor, may increase the bioaccumulation of other chemicals, and can interfere with photosynthesis in some aquatic plants and algae.
A brown product also darkens the water and reduces light penetration, which affects phytoplankton and the pond’s oxygen balance. Documents and laboratory checks reduce uncertainty about what is in a product, but they do not show how a pond will respond.
FAQ
Does your sodium humate TDS list aquaculture use?
No. Our sodium humate TDS does not list aquaculture use. This checklist is general guidance for evaluating any humate product.
Is an SDS that says “not classified” enough for pond use?
No. An SDS classification covers hazards under chemical classification rules. It is not an aquatic safety assessment and says nothing specific about effects on a pond ecosystem.
Why do two suppliers’ humic acid figures not match?
They may use different test methods, or report on a dry versus as-is basis. Compare only figures with the same method and basis.
Which heavy metals should be tested?
At least lead, cadmium, arsenic, mercury and chromium, or whatever list your local standard requires. Ask your supplier for a heavy-metal test report for the batch you will receive.
Should I test solubility in tap water?
Use the pond water itself. Hardness affects whether dissolved humate stays in solution.
References
- Boyd CE, Tucker CS. 1998. Pond Aquaculture Water Quality Management. Springer. doi:10.1007/978-1-4615-5407-3
- Steinberg CEW, Kamara S, Prokhotskaya VY, et al. 2006. Dissolved humic substances – ecological driving forces from the individual to the ecosystem level? Freshwater Biology 51:1189–1210. doi:10.1111/j.1365-2427.2006.01571.x






