Humic acid, humate and fulvic acid supplier · Own factory in Shanxi, China

Email: info@humicacid.org

Home / Blog

Quality Testing for Feed-Grade Sodium Humate: What a Certificate of Analysis Should Show

Feed manufacturers and premix companies that buy sodium humate need more than a product name and a price. They need to know that each batch matches the specification, and they need documents that their own quality system can accept. This article explains what a Certificate of Analysis (COA) for feed-grade sodium humate should contain, how the main items are tested, and which questions to ask.

This article is about quality testing and documents. It does not cover effects in animals or inclusion rates. Whether and how sodium humate may be used in feed depends on the feed regulations of the destination country, and the inclusion rate must be set by a qualified feed professional for the species and diet. For the product itself, see the Sodium Humate Feed Grade page.

1. Specification, TDS and COA: three different documents

  • Specification / Technical Data Sheet (TDS). States the typical or minimum values the product is made to. It describes the grade, not a particular batch.
  • Certificate of Analysis (COA). Reports the measured results for one batch, with the batch number, the test methods and the date. This is the document your quality team checks on arrival.
  • Safety Data Sheet (SDS). Covers hazards, handling, storage, transport and disposal. It is not a quality document, but it is usually required before a new material is accepted by the buyer.

A COA without a batch number, a date or test methods is of little use. Ask for all three before you place a first order.

2. The main quality items

Our feed-grade sodium humate is supplied as a feed material, in powder (SHA-NaHA-feed-P) and flake (SHA-NaHA-feed-F) form. The typical values on the current TDS are:

ItemSHA-NaHA-feed-P (powder)SHA-NaHA-feed-F (flake)
Humic acid (dry basis)≥60%≥60%
Water solubility100%100%
Moisture≤12%≤12%
pH9–109–10
Particle size60–80 mesh2–5 mm
Heavy metalsBatch COA available on requestBatch COA available on request

The sections below explain what each item means and how it is usually tested.

Humic acid content

This is the main quality figure, but it is also the one most affected by the test method.

  • The method must be named. Results from different methods can differ a lot for the same sample. The standardized method published by Lamar et al. (2014), the basis of ISO 19822:2018, measures humic acid by acid precipitation and fulvic acid on a resin, and usually gives lower numbers than many older methods.
  • The basis must be stated. Dry basis (moisture excluded) or as received. For a product with 12% moisture, the difference is significant.
  • Compare like with like. If you are comparing suppliers, ask each one for results by the same method, or have samples tested by one independent laboratory.

Moisture

Moisture affects how much dry product you actually buy, and how well the product stores. Moisture is usually measured by drying a sample at a set temperature to constant weight. Sodium humate takes up water from humid air, so moisture can rise after production if bags are opened or stored in damp conditions. Check moisture on arrival as well as on the COA.

Water solubility and insoluble matter

For a feed-grade material, water solubility shows how much of the product dissolves and how much mineral residue remains. It is measured by dissolving a weighed sample, filtering, and weighing the insoluble residue. Our feed grade is listed as 100% water-soluble.

pH

Sodium humate solutions are alkaline. Our feed grades are pH 9–10. Always check the dilution, because pH at 1:10 is not comparable with pH at 1:100. A pH of 9–10 is consistent with a sodium salt from alkaline extraction.

Particle size

Particle size affects mixing, dust and flow in premix and feed plants. It is reported as mesh range (powder) or millimetres (flake) and is checked by sieving.

Sodium

Sodium humate brings sodium into the diet. Nutritionists who calculate dietary electrolyte balance should include this sodium in their calculations. Sodium content is not stated on our current TDS; if you need it for formulation, have it measured on a sample.

Heavy metals and other contaminants

Feed regulations in most markets set maximum levels for undesirable substances such as arsenic, lead, cadmium and mercury, and some also require tests for other contaminants. Humic materials come from geological sources, so these elements must be tested batch by batch by a competent laboratory.

For our grades, a batch COA is available on request.

3. How heavy metals are usually tested

Laboratories usually digest the sample in acid and then measure the elements by instrument methods such as ICP-MS, ICP-OES or atomic absorption spectroscopy; mercury is commonly measured by cold-vapour atomic absorption or a dedicated mercury analyser. When you read a heavy metal result, check:

  • the element and the result, with units (mg/kg),
  • the method and the laboratory’s limit of detection,
  • whether the result is on the product as received or on a dry basis,
  • and whether the laboratory is accredited for that test.

“Not detected” is only meaningful if the detection limit is stated.

4. Batch traceability

A reliable supply chain needs records that link the bag in your warehouse to the production batch and the COA:

  • Batch number on every bag, matching the COA.
  • Production date on the bag and the COA.
  • Retained samples. Ask whether the supplier keeps a retained sample from each batch, and for how long. If there is a question later, the sample can be re-tested.
  • Consistent packaging. Bag type, net weight and label should match the order and the documents.

5. Testing on arrival

Even with a good COA, many buyers run their own checks on arrival:

  1. Check the batch number and labels against the COA.
  2. Look at the product: colour, form, lumps, foreign matter.
  3. Measure moisture.
  4. Send a sample to your own or an independent laboratory for humic acid (by a stated method) and for contaminants, at least for the first batches.
  5. Keep a retained sample of each batch you receive.

6. Questions to ask a supplier

  1. Which method do you use for humic acid? Is the result on a dry basis?
  2. Can you send a COA for a recent batch, with batch number, date and methods?
  3. Which laboratory tests heavy metals, and by which method? What are the detection limits?
  4. Is the sodium content measured? If not, can a sample be tested?
  5. Do you keep retained samples? For how long?
  6. Can you send the TDS and SDS?

7. What this article does not cover

This article does not describe effects in animals, inclusion rates, or regulatory status. Those depend on the species, the diet and the law in the destination country.

For the specification and documents of our feed grade, see the Sodium Humate Feed Grade page, or contact us.

References

  • Lamar, R.T., Olk, D.C., Mayhew, L., Bloom, P.R. (2014). A new standardized method for quantification of humic and fulvic acids in humic ores and commercial products. Journal of AOAC International, 97(3), 721–730.
  • ISO 19822:2018. Fertilizers and soil conditioners — Determination of humic and hydrophobic fulvic acids concentrations in fertilizer materials.

Product figures are typical values from our current TDS (SHA-NaHA-feed-P, SHA-NaHA-feed-F). Batch COA available on request.